TEL. & FAX +66(0)2-020-3301
 |
 |
 |
NPort® 5600-8-DTL device servers can conveniently and transparently connect 8 serial devices to an Ethernet network, allowing you to network your existing serial devices with basic configurations. You can both centralize management of your serial devices and distribute management hosts over the network. The NPort® 5600-8-DTL device servers have a smaller form factor than our 19-inch models, making them a great choice for applications that need additional serial ports when mounting rails are not available.
The NPort® 5650-8-DTL device servers support selectable 1 kilo-ohm and 150 kilo-ohms pull high/low resistors and a 120-ohm terminator. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals. When using termination resistors, it is also important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible with all environments, NPort® 5600-8-DTL device servers use DIP switches to allow users to adjust termination and pull high/low resistor values manually for each serial port.
The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The NPort® 5600’s LEDs not only indicate current system and network status, but they also help field engineers monitor the status of attached serial devices.
Ethernet Interface | |
| 10/100BaseT(X) Ports (RJ45 connector) | 1 |
| Magnetic Isolation Protection | 1.5 kV (built-in) |
Ethernet Software Features | |
| Configuration Options | Serial Console, Telnet Console, Web Console (HTTP/HTTPS), Windows Utility |
| Management | ARP, BOOTP, DHCP Client, DNS, HTTP, HTTPS, ICMP, IPv4, LLDP, Rtelnet, SMTP, SNMPv1/v2c, Telnet, TCP/IP, UDP |
| Filter | IGMP v1/v2 |
| Windows Real COM Drivers | Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded |
| Linux Real TTY Drivers | Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x |
| Fixed TTY Drivers | SCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6.x, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X |
| Android API | Android 3.1.x and later |
| MIB | RFC1213, RFC1317 |
| Time Management | SNTP |
Serial Interface | |
| Connector | DB9 male |
No. of Ports | 8 |
| Serial Standards | NPort 5610-8-DTL Series: RS-232 NPort 5650-8-DTL Series: RS-232, RS-422, RS-485 |
| Baudrate | Supports standard baudrates (unit=bps): 50, 75, 110, 134, 150, 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 19200, 38400, 57600, 115200, 230.4k, 460.8k, 921.6k |
| Data Bits | 5, 6, 7, 8 |
| Stop Bits | 1, 1.5, 2 |
| Parity | None, Even, Odd, Space, Mark |
| Flow Control | RTS/CTS, DTR/DSR, XON/XOFF |
| Isolation | NPort 5650I-8-DTL Series: 2 kV |
| Pull High/Low Resistor for RS-485 | 1 kilo-ohm, 150 kilo-ohms |
| RS-485 Data Direction Control | ADDC® (automatic data direction control) |
| Terminator for RS-485 | NPort 5650 Series: 120 ohms |
Serial Signals | |
| RS-232 | TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND |
| RS-422 | Tx+, Tx-, Rx+, Rx-, GND |
| RS-485-4w | Tx+, Tx-, Rx+, Rx-, GND |
| RS-485-2w | Data+, Data-, GND |
Power Parameters | |
| Input Current | NPort 5610-8-DTL Series: 340 mA @ 12 VDC NPort 5650-8-DTL Series: 470 mA @ 12 VDC NPort 5650I-8-DTL Series: 740 mA @ 12 VDC |
| No. of Power Inputs | 1 |
| Input Voltage | 12 to 48 VDC |
| Reverse Polarity Protection | Supported |
| Source of Input Power | Power input jack |
Physical Characteristics | |
| Housing | Metal |
| Dimensions (with ears) | 229 x 135.43 x 46 mm (9.02 x 5.33 x 1.81 in) |
| Dimensions (without ears) | 197 x 135.43 x 44 mm (7.76 x 5.33 x 1.73 in) |
| Weight | NPort 5610-8-DTL Series: 1760 g (3.88 lb) NPort 5650-8-DTL Series: 1770 g (3.90 lb) NPort 5650I-8-DTL Series: 1850 g (4.08 lb) |
| Installation | Desktop, DIN-rail mounting (with optional kit), Wall mounting (with optional kit) |
Environmental Limits | |
| Operating Temperature | Standard Models: 0 to 60°C (-32 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
| Storage Temperature (package included) | -40 to 75°C (-40 to 167°F) |
| Ambient Relative Humidity | 5 to 95% (non-condensing) |
Standards and Certifications | |
| EMC | EN 55032/24 |
| EMI | CISPR 32, FCC Part 15B Class A |
| EMS | IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m IEC 61000-4-8 PFMF IEC 61000-4-11 DIPs |
| Safety | UL 60950-1 |
Declaration | |
| Green Product | RoHS, CRoHS, WEEE |
MTBF | |
| Time | NPort 5610-8-DTL Series: 953,388 hrs NPort 5650-8-DTL Series: 740,457 hrs NPort 5650I-8-DTL Series: 258,150 hrs |
| Standards | Telcordia (Bellcore) Standard TR/SR |
Warranty | |
| Warranty Period | 5 years |
| Details | See www.moxa.com/warranty |
| Name | Type | Version | Release Date | |
| Datasheet for NPort 5600-DTL Series | Datasheet | V1.2 | 08 November 2019 |
| Serial Interface | RS-232 |
| Serial Interface Connector | DB9 |
| Serial Interface Isolation | - |
| Operating Temp. | 0 to 60°C |
| Input Voltage | 12-48 VDC |
| Serial Interface | RS-232/422/485 |
| Serial Interface Connector | DB9 |
| Serial Interface Isolation | - |
| Operating Temp. | 0 to 60°C |
| Input Voltage | 12-48 VDC |
| Serial Interface | RS-232/422/485 |
| Serial Interface Connector | DB9 |
| Serial Interface Isolation | 2 kV |
| Operating Temp. | 0 to 60°C |
| Input Voltage | 12-48 VDC |
| Serial Interface | RS-232 |
| Serial Interface Connector | DB9 |
| Serial Interface Isolation | - |
| Operating Temp. | -40 to 75°C |
| Input Voltage | 12-48 VDC |
| Serial Interface | RS-232/422/485 |
| Serial Interface Connector | DB9 |
| Serial Interface Isolation | - |
| Operating Temp. | -40 to 75°C |
| Input Voltage | 12-48 VDC |
| Serial Interface | RS-232/422/485 |
| Serial Interface Connector | DB9 |
| Serial Interface Isolation | 2 kV |
| Operating Temp. | -40 to 75°C |
| Input Voltage | 12-48 VDC |
Notice: Undefined variable: detail_ap in /opt/lampp/htdocs/productview.php on line 639
